Products
SCB10 3500kVA 11kV 415V Dry Type Transformer
  • SCB10 3500kVA 11kV 415V Dry Type TransformerSCB10 3500kVA 11kV 415V Dry Type Transformer
  • SCB10 3500kVA 11kV 415V Dry Type TransformerSCB10 3500kVA 11kV 415V Dry Type Transformer
  • SCB10 3500kVA 11kV 415V Dry Type TransformerSCB10 3500kVA 11kV 415V Dry Type Transformer

SCB10 3500kVA 11kV 415V Dry Type Transformer

The SCB10 3500kVA 11kV 415V dry type transformer is a high performance cast resin transformer designed for reliable power distribution in demanding environments. With a rated capacity of 3500kVA, primary voltage of 11kV, and secondary voltage of 415V, this transformer offers excellent electrical safety, low maintenance, and superior thermal performance.
Wenzhou Xifa Electrical Equipment Co., Ltd., as a professional manufacturer of oil immersed and dry type transformers, has established a rigorous production process covering procurement, manufacturing, and final product inspection. In our factory, factory acceptance testing is not a sampling procedure but a mandatory 100% full inspection for every single transformer. The tests are conducted in accordance with the latest domestic and international standards, using calibrated high precision testing equipment. Key electrical parameters of the transformer,such as voltage ratio, impedance, losses, and insulation strength are verified item by item. Only products that pass all test items without exception are granted permit. This rigorous testing system is our technical guarantee for the promise that "every transformer we deliver is trustworthy.

Production Process of SCB10 3500kVA 11kV 415V dry type transformer

I.Core Manufacturing

The core is the central path for electromagnetic induction, and its manufacturing precision directly affects transformer performance.

1.Cutting and Blanking: High quality silicon steel strip is cut longitudinally and transversely into sheets of required width and length. The cut edges must have minimal burrs and high dimensional accuracy to maintain good magnetic permeability.

2.Punching and Stacking: The cut silicon steel sheets are punched (e.g., for holes) and then stacked layer by layer according to the drawing to form a complete, multi step core leg.

3.Insulation Sealing: After stacking, epoxy resin is brushed or sealed onto the end and surface of the core for insulation and protection against rust.

II. Coil Manufacturing

This is the most complex and critical part of SCB10 3500kVA 11kV 415V dry type transformer

 production. The goal is to create windings that carry voltage and current and seal them with epoxy resin into a solid, insulated structure.

1.Coil Winding: On a dedicated winding machine, copper foil or copper wire is wound onto a mandrel to form the high voltage (HV) and low voltage (LV) windings. During winding, interlayer insulation, end insulation, and leads are precisely placed.

2.Pre drying and Molding: The wound coil is cleaned and placed into a casting mold. The assembly is then sent to an oven for pre drying. This step is crucial; moisture must be completely removed from the coil, as residual moisture would cause air pockets after casting, severely compromising insulation performance.

3.Vacuum Casting: This is the core process determining product life. The dried coil inside its mold is placed into a vacuum casting tank, where a high vacuum ,pressure can drop below 100 Pa is drawn. Simultaneously, a precise mixture of epoxy resin, hardener, and filler (e.g., silica powder) is blended and degassed. Under vacuum, the mixture is poured into the mold, ensuring it penetrates all coil gaps and the final product is free of bubbles.

4.High Temperature Curing: After casting, the mold is placed into a curing oven for high temperature curing. A multi stage temperature ramp (e.g., from 75°C to 135°C in steps) is typically used. This allows the epoxy resin to fully react chemically, forming a hard, heat resistant, solid mass with excellent insulating properties.

5.Demolding and Finishing: After curing, the mold is removed. The coil's surface is ground, trimmed, and chamfered to achieve a smooth finish and precise dimensions, ready for the next stage.

Scb10 3500kva 11kv 415v Dry Type TransformerScb10 3500kva 11kv 415v Dry Type Transformer

Product Parameters:

Name

SCB10 3500kVA 11kV 415V dry type transformer

Rated Capacity

3500kva

Primary voltage

11KV

Secondary voltage

415V

Insulation material

Cast resin

Vector Group

Dyn11 Yyn0

No load Loss (P0)

Based on customer’s requirement

Load Loss (Pk) @ 120°C

Based on customer’s requirement

Impedance Voltage (Uk)

8%

Insulation Class

CLASS F or H

Cooling method

ONAF ONAF

Partial discharge

Less than 10pc


Producing Equipment

Producing EquipmentProducing EquipmentProducing EquipmentProducing Equipment

Semi Finished Product

Protection Enclosure IP21

Protection Enclosure IP21

Transformer Core

Transformer Core

Transformer Winding

Transformer Winding

Test Center

Testing CenterTesting CenterTesting Center

Winding Workshop

Winding WorkshopWinding WorkshopWinding WorkshopWinding Workshop


Send Inquiry
Contact Info

To get your quotation ASAP

XiFa-your reliable electrical equipment supplier
X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
RejectAccept